CANalyst II

(7 intermediate revisions by the same user not shown)

Line 1:

[[File:CANalystII-above.png|thumb|right|alt=Picture of the CANalyst II from above.|The CANalyst II, an enigma (for now).]]

The Canalyst II is an affordable, well-built piece of very Chinese equipment, exposing two [[CAN bus]] ~~bus~~ transceivers to a USB CAN adapter capable of 7k fps, and megabit CAN networks. There is very little English documentation. It appears as USB VendorID 04d8, ProductID 0053 (04d8:0053), the space of [https://www.microchip.com/ Microchip Technology, Inc.]. Both channels come equipped with independently-selectable 120Ω resistors necessary for ISO 11898-2 High-Speed CAN buses (such a resistor should not be used with ISO 11898-3 Reliable CAN buses). ~~Note that the manual refers to ohms as "euros", which is pretty indicative of its quality overall~~.

The Canalyst II is an affordable, well-built piece of very Chinese equipment, exposing two [[CAN bus]] transceivers to a USB CAN adapter capable of 7k fps, and megabit CAN networks. There is very little English documentation. It appears as USB VendorID 04d8, ProductID 0053 (04d8:0053), the space of [https://www.microchip.com/ Microchip Technology, Inc.]. Both channels come equipped with independently-selectable 120Ω resistors necessary for ISO 11898-2 High-Speed CAN buses (such a resistor should not be used with ISO 11898-3 Reliable CAN buses). It also offers baud rate detection functionality.

I suspect there to be an [https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/stand-alone-can-controller:SJA1000T SJA1000] chip inside, but have not verified this.

Note that the manual refers to ohms as euros, which is pretty indicative of the documentation's quality overall.

I suspect there to be a 16MHz [https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/stand-alone-can-controller:SJA1000T SJA1000] chip inside, but have not verified this.

==Hardware==

[[File:CANalystII-test-setup.png|thumb|left|alt=Wiring diagram for self-test|Wired thusly, the CANalyst II can self-test both channels.]]

The CANalyst II is powered entirely over its USB connection--there is no dedicated input for power.

Upon being powered on, the red PWR LED lights up. The blue SYS LED lights once whenever the OS makes a connection to the device. A self-test capability is included on the device, which will see the blue LED light twice in succession on a successful test. The wiring diagram for the self-test mode can be seen to the left. The CANalyst II presents a senary [https://en.wikipedia.org/wiki/Screw_terminal screw terminal] suitable for mating with a [https://en.wikipedia.org/wiki/D-subminiature DE-9] or [https://en.wikipedia.org/wiki/Data_link_connector_(automotive) ODB-II DLC].

{| class="wikitable sortable"

|-

!Port !! Pin !! Name !! Function

|-

| rowspan="6" | [[File:6screwterm.jpg|thumb]] || 1 || CAN_H || CAN_H signal wire, channel 0

|-

| 2 || SHIELD || Terminal resistance connector, channel 0

|-

| 3 || CAN_L || CAN_L signal wire, channel 0

|-

| 4 || CAN_H || CAN_H signal wire, channel 1

|-

| 5 || SHIELD || Terminal resistance connector, channel 1

|-

| 6 || CAN_L || CAN_L signal wire, channel 1

|-

|}

The Chinese manufacturer's site claims that the device is "similar to a [https://www.zlg.com/can/can/product/id/22.html ZLG USBCAN-II+]". What exactly is meant by "similar" here is not yet known. The USBCAN-II+ claims 14Kfps using both channels, which does match the claimed performance of the CANalyst II.

==Linux==

CANalyst II: Difference between revisions

Dank (talk | contribs)

@@ Line 1: / Line 1: @@
 [[File:CANalystII-above.png|thumb|right|alt=Picture of the CANalyst II from above.|The CANalyst II, an enigma (for now).]]
-The Canalyst II is an affordable, well-built piece of very Chinese equipment, exposing two [[CAN bus]] bus transceivers to a USB CAN adapter capable of 7k fps, and megabit CAN networks. There is very little English documentation. It appears as USB VendorID 04d8, ProductID 0053 (04d8:0053), the space of [https://www.microchip.com/ Microchip Technology, Inc.]. Both channels come equipped with independently-selectable 120Ω resistors necessary for ISO 11898-2 High-Speed CAN buses (such a resistor should not be used with ISO 11898-3 Reliable CAN buses). Note that the manual refers to ohms as "euros", which is pretty indicative of its quality overall.
+The Canalyst II is an affordable, well-built piece of very Chinese equipment, exposing two [[CAN bus]] transceivers to a USB CAN adapter capable of 7k fps, and megabit CAN networks. There is very little English documentation. It appears as USB VendorID 04d8, ProductID 0053 (04d8:0053), the space of [https://www.microchip.com/ Microchip Technology, Inc.]. Both channels come equipped with independently-selectable 120Ω resistors necessary for ISO 11898-2 High-Speed CAN buses (such a resistor should not be used with ISO 11898-3 Reliable CAN buses). It also offers baud rate detection functionality.
-I suspect there to be an [https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/stand-alone-can-controller:SJA1000T SJA1000] chip inside, but have not verified this.
+Note that the manual refers to ohms as euros, which is pretty indicative of the documentation's quality overall.
+I suspect there to be a 16MHz [https://www.nxp.com/products/analog/interfaces/in-vehicle-network/can-transceiver-and-controllers/stand-alone-can-controller:SJA1000T SJA1000] chip inside, but have not verified this.
+==Hardware==
+[[File:CANalystII-test-setup.png|thumb|left|alt=Wiring diagram for self-test|Wired thusly, the CANalyst II can self-test both channels.]]
+The CANalyst II is powered entirely over its USB connection--there is no dedicated input for power.
+Upon being powered on, the red PWR LED lights up. The blue SYS LED lights once whenever the OS makes a connection to the device. A self-test capability is included on the device, which will see the blue LED light twice in succession on a successful test. The wiring diagram for the self-test mode can be seen to the left. The CANalyst II presents a senary [https://en.wikipedia.org/wiki/Screw_terminal screw terminal] suitable for mating with a [https://en.wikipedia.org/wiki/D-subminiature DE-9] or [https://en.wikipedia.org/wiki/Data_link_connector_(automotive) ODB-II DLC].
+{| class="wikitable sortable"
+|-
+!Port !! Pin !! Name !! Function
+|-
+| rowspan="6" | [[File:6screwterm.jpg|thumb]] || 1 || CAN_H || CAN_H signal wire, channel 0
+|-
+| 2 || SHIELD || Terminal resistance connector, channel 0
+|-
+| 3 || CAN_L || CAN_L signal wire, channel 0
+|-
+| 4 || CAN_H || CAN_H signal wire, channel 1
+|-
+| 5 || SHIELD || Terminal resistance connector, channel 1
+|-
+| 6 || CAN_L || CAN_L signal wire, channel 1
+|-
+|}
+The Chinese manufacturer's site claims that the device is "similar to a [https://www.zlg.com/can/can/product/id/22.html ZLG USBCAN-II+]". What exactly is meant by "similar" here is not yet known. The USBCAN-II+ claims 14Kfps using both channels, which does match the claimed performance of the CANalyst II.
 ==Linux==