Check out my first novel, midnight's simulacra!

Ethernet: Difference between revisions

From dankwiki
No edit summary
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
==10GigE==
===10GBASE-T===
* Reuses the existing 1000BASE-T MAC
* Full duplex only
* 4 connector, 4 twisted pairs (lanes) copper cabling
* 10-level PAM code (3 bits/symbol)
* Retains 8-state 4D trellis code across pairs
* 833 Mbaud, ~450MHz bandwidth
* Echo-cancelled transmission, FEXT cancellation
** 10Gbps = 4 lanes * 833 Mbaud * 3 bits/baud
===10GBASE-CX4===
* Short distance copper twin-ax
==GigE==
* 5-level PAM code (2 bits/symbol)
* 125 Mbaud, ~80MHz bandwidth
==Fast Ethernet==
==Addresses==
==Addresses==
An address is ''unicast'' if the least significant bit of the first byte is 0. Otherwise, it is either ''broadcast'':
An address is ''unicast'' if the least significant bit of the first byte is 0. Otherwise, it is either ''broadcast'':
Line 9: Line 25:
* (224.0.0.251, ff02::fb): mDNS
* (224.0.0.251, ff02::fb): mDNS
* 33:33:00:01:00:02 (ff02::1:2): DHCPv6 server/relay
* 33:33:00:01:00:02 (ff02::1:2): DHCPv6 server/relay
===Locally-assigned Addresses===
If the penultimately-significant bit is 1, the address is "locally assigned" (read: made up). This is used by the Linux kernel's rand_hw_addr() function, used by PPP and TAP.
==See Also==
* [http://wiki.wireshark.org/Ethernet Ethernet page] on the Wireshark wiki
* Ethernet is specified in the IEEE 802.3 [[standards]]
* "[[Media:IEEE_802_10GBASE-T_Tutorial.pdf|IEEE 802 10GBASE-T Tutorial]]" from the IEEE working group, 2003
[[CATEGORY: Networking]]
[[CATEGORY: Networking]]

Latest revision as of 09:20, 13 June 2012

10GigE

10GBASE-T

  • Reuses the existing 1000BASE-T MAC
  • Full duplex only
  • 4 connector, 4 twisted pairs (lanes) copper cabling
  • 10-level PAM code (3 bits/symbol)
  • Retains 8-state 4D trellis code across pairs
  • 833 Mbaud, ~450MHz bandwidth
  • Echo-cancelled transmission, FEXT cancellation
    • 10Gbps = 4 lanes * 833 Mbaud * 3 bits/baud

10GBASE-CX4

  • Short distance copper twin-ax

GigE

  • 5-level PAM code (2 bits/symbol)
  • 125 Mbaud, ~80MHz bandwidth

Fast Ethernet

Addresses

An address is unicast if the least significant bit of the first byte is 0. Otherwise, it is either broadcast:

  • FF:FF:FF:FF:FF:FF: segment broadcast

or multicast:

Local Network Control Block (224.0.0/24)

  • 01:00:5e:00:00:01 (224.0.0.1): All-Hosts
  • 01:00:5e:00:00:02 (224.0.0.2): All-Routers
  • (224.0.0.22): IGMP
  • (224.0.0.251, ff02::fb): mDNS
  • 33:33:00:01:00:02 (ff02::1:2): DHCPv6 server/relay

Locally-assigned Addresses

If the penultimately-significant bit is 1, the address is "locally assigned" (read: made up). This is used by the Linux kernel's rand_hw_addr() function, used by PPP and TAP.

See Also