Check out my first novel, midnight's simulacra!
Monoprice Voxel 3D Printer: Difference between revisions
From dankwiki
(Created page with "The [https://www.monoprice.com/product?p_id=33820 Monoprice Voxel] is an affordable 3D printer. ==Calibration== * Enter calibration mode using the on-screen display. * Lay a...") |
No edit summary |
||
| (11 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
The [https://www.monoprice.com/product?p_id=33820 Monoprice Voxel] is an affordable 3D printer. | The [https://www.monoprice.com/product?p_id=33820 Monoprice Voxel] is an affordable 3D printer using 1.75mm filament. It is said to be a rebranded [https://flashforge-usa.com/products/adventurer-3 FlashForge Adventurer 3], which seems plausible from external appearance. I believe it to have "Sailfish" flavored GCode. | ||
The build area is 150mm x 150mm x 150mm. The nozzle diameter is 0.4mm. | |||
It claims to support 3MF, STL, OBJ, FPP, BMP, PNG, and JPG via its slicing software; GX and G are directly supported. | |||
==Calibration== | ==Calibration== | ||
* Enter calibration mode using the on-screen display. | * Enter calibration mode using the on-screen display. | ||
* | * The nozzle will be lowered by the device. | ||
* Use up/ | * Fine-tune the nozzle until a piece of paper can just slide underneath it. | ||
** Use the up and down buttons on the touchscreen | |||
==Software== | |||
Monoprice makes the [https://www.matterhackers.com/store/l/mattercontrol/sk/MKZGTDW6 MatterControl] software available as a deb. Installing it on my [[Debian|Debian Unstable]] machine in October 2019 saw it crash a lot. Most of these were due to missing dependencies; make sure you've installed: | |||
* gnome-themes-standard | |||
* mono-vbnc | |||
==Printing from USB storage== | |||
* The camera disables USB storage. The camera ''must be turned off'' to print from USB. | |||
* The USB storage must be formatted with an old DOS-style partition table, as far as I can tell. | |||
* The gcode files must have a ''.g'' extension. | |||
* Select "build" from the main menu | |||
* Insert the USB drive, and wait for an icon to show up at the top indicating it has been mounted. Once this happens, the flash drive source will become available. | |||
* Select the flash drive, and select your gcode file. | |||
==Accessing the printer== | |||
For hostname <tt>voxel.localnet</tt>, use http://voxel.localnet/?action=stream to access the camera. | |||
[[CATEGORY: 3D Printing]] | |||
Latest revision as of 03:27, 1 September 2024
The Monoprice Voxel is an affordable 3D printer using 1.75mm filament. It is said to be a rebranded FlashForge Adventurer 3, which seems plausible from external appearance. I believe it to have "Sailfish" flavored GCode.
The build area is 150mm x 150mm x 150mm. The nozzle diameter is 0.4mm.
It claims to support 3MF, STL, OBJ, FPP, BMP, PNG, and JPG via its slicing software; GX and G are directly supported.
Calibration
- Enter calibration mode using the on-screen display.
- The nozzle will be lowered by the device.
- Fine-tune the nozzle until a piece of paper can just slide underneath it.
- Use the up and down buttons on the touchscreen
Software
Monoprice makes the MatterControl software available as a deb. Installing it on my Debian Unstable machine in October 2019 saw it crash a lot. Most of these were due to missing dependencies; make sure you've installed:
- gnome-themes-standard
- mono-vbnc
Printing from USB storage
- The camera disables USB storage. The camera must be turned off to print from USB.
- The USB storage must be formatted with an old DOS-style partition table, as far as I can tell.
- The gcode files must have a .g extension.
- Select "build" from the main menu
- Insert the USB drive, and wait for an icon to show up at the top indicating it has been mounted. Once this happens, the flash drive source will become available.
- Select the flash drive, and select your gcode file.
Accessing the printer
For hostname voxel.localnet, use http://voxel.localnet/?action=stream to access the camera.
