Filaments

Line 30:

==Bambu filaments parameter table==

{| wikiclass="table" border="1"

! Parameter !! PLA Aero !! ASA !! ASA Aero !! PC

! Parameter !! PLA Aero !! ASA !! ASA Aero !! PC !! ABS

|-

| Print temp C || 210-260 || 240-270 || 240-280 || 250-270

| Print temp C || 210-260 || 240-270 || 240-280 || 250-270 || 240-270

|-

| Print speed mm/s || <180 || <250 || <150 || <300

| Print speed mm/s || <180 || <250 || <150 || <300 || <300

|-

| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80 ||

| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80 || ||

|-

| Filament density g/cm³ || 1.21 || 1.05 || 0.99 || 1.2

| Filament density g/cm³ || 1.21 || 1.05 || 0.99 || 1.2 || 1.05

|-

| Foaming rate || 0-120 || n/a || 0-110 || n/a

| Foaming rate || 0-120 || n/a || 0-110 || n/a || n/a

|-

| Vol. expansion ratio || 100-220 || 102 || 100-210 ||

| Vol. expansion ratio || 100-220 || 102 || 100-210 || ||

|-

| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97 ||

| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97 || ||

|-

| Tensile strength MPa || 24±2 || 37±3 || 32±4 || 55±4

| Tensile strength MPa || 24±2 || 37±3 || 32±4 || 55±4 || 33±3

|-

| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6 || 3.8±0.3

| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6 || 3.8±0.3 || 10.5±1.0

|-

| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120 || 2310±70

| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120 || 2310±70 || 1880±110

|-

| Bending strength MPa || 45±4 || 65±5 || 58±6 || 108±4

| Bending strength MPa || 45±4 || 65±5 || 58±6 || 108±4 || 62±4

|-

| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5 || 34.8±2.1

| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5 || 34.8±2.1 || 39±3.6

|-

| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5 || 32.2±2.9

| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5 || 32.2±2.9 || 34.2±3.8

|-

| Melting temp C || 153 || 210 || 204 || 228

| Melting temp C || 153 || 210 || 204 || 228 || 200

|-

| Heat deflection temp C || 53 || 100 || 85 || 117

| Heat deflection temp C || 53 || 100 || 85 || 117 || 87

|-

| Vicat softening temp C || 54 || 106 || 80 || 119

| Vicat softening temp C || 54 || 106 || 80 || 119 || 94

|-

|}

Filaments: Difference between revisions

Dank (talk | contribs)

@@ Line 30: / Line 30: @@
 ==Bambu filaments parameter table==
 {| wikiclass="table" border="1"
-! Parameter !! PLA Aero !! ASA !! ASA Aero !! PC
+! Parameter !! PLA Aero !! ASA !! ASA Aero !! PC !! ABS
 |-
-| Print temp C || 210-260 || 240-270 || 240-280 || 250-270
+| Print temp C || 210-260 || 240-270 || 240-280 || 250-270 || 240-270
 |-
-| Print speed mm/s || <180 || <250 || <150 || <300
+| Print speed mm/s || <180 || <250 || <150 || <300 || <300
 |-
-| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80 ||
+| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80 || ||
 |-
-| Filament density g/cm³ || 1.21 || 1.05 || 0.99 || 1.2
+| Filament density g/cm³ || 1.21 || 1.05 || 0.99 || 1.2 || 1.05
 |-
-| Foaming rate || 0-120 || n/a || 0-110 || n/a
+| Foaming rate || 0-120 || n/a || 0-110 || n/a || n/a
 |-
-| Vol. expansion ratio || 100-220 || 102 || 100-210 ||
+| Vol. expansion ratio || 100-220 || 102 || 100-210 || ||
 |-
-| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97 ||
+| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97 || ||
 |-
-| Tensile strength MPa || 24±2 || 37±3 || 32±4 || 55±4
+| Tensile strength MPa || 24±2 || 37±3 || 32±4 || 55±4 || 33±3
 |-
-| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6 || 3.8±0.3
+| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6 || 3.8±0.3 || 10.5±1.0
 |-
-| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120 || 2310±70
+| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120 || 2310±70 || 1880±110
 |-
-| Bending strength MPa || 45±4 || 65±5 || 58±6 || 108±4
+| Bending strength MPa || 45±4 || 65±5 || 58±6 || 108±4 || 62±4
 |-
-| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5 || 34.8±2.1
+| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5 || 34.8±2.1 || 39±3.6
 |-
-| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5 || 32.2±2.9
+| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5 || 32.2±2.9 || 34.2±3.8
 |-
-| Melting temp C || 153 || 210 || 204 || 228
+| Melting temp C || 153 || 210 || 204 || 228 || 200
 |-
-| Heat deflection temp C || 53 || 100 || 85 || 117
+| Heat deflection temp C || 53 || 100 || 85 || 117 || 87
 |-
-| Vicat softening temp C || 54 || 106 || 80 || 119
+| Vicat softening temp C || 54 || 106 || 80 || 119 || 94
 |-
 |}