Filaments

Line 30:

==Bambu filaments parameter table==

{| wikiclass="table" border="1"

! Parameter !! PLA Aero !! ASA !! ASA Aero

! Parameter !! PLA Aero !! ASA !! ASA Aero !! PC

|-

| Print temp C || 210-260 || 240-270 || 240-280

| Print temp C || 210-260 || 240-270 || 240-280 || 250-270

|-

| Print speed mm/s || <180 || <250 || <150

| Print speed mm/s || <180 || <250 || <150 || <300

|-

| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80

| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80 ||

|-

| Filament density g/cm³ || 1.21 || 1.05 || 0.99

| Filament density g/cm³ || 1.21 || 1.05 || 0.99 || 1.2

|-

| Foaming rate || 0-120 || n/a || 0-110

| Foaming rate || 0-120 || n/a || 0-110 || n/a

|-

| Vol. expansion ratio || 100-220 || 102 || 100-210

| Vol. expansion ratio || 100-220 || 102 || 100-210 ||

|-

| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97

| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97 ||

|-

| Tensile strength MPa || 24±2 || 37±3 || 32±4

| Tensile strength MPa || 24±2 || 37±3 || 32±4 || 55±4

|-

| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6

| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6 || 3.8±0.3

|-

| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120

| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120 || 2310±70

|-

| Bending strength MPa || 45±4 || 65±5 || 58±6

| Bending strength MPa || 45±4 || 65±5 || 58±6 || 108±4

|-

| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5

| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5 || 34.8±2.1

|-

| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5

| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5 || 32.2±2.9

|-

| Melting temp C || 153 || 210 || 204

| Melting temp C || 153 || 210 || 204 || 228

|-

| Heat deflection temp C || 53 || 100 || 85

| Heat deflection temp C || 53 || 100 || 85 || 117

|-

| Vicat softening temp C || 54 || 106 || 80

| Vicat softening temp C || 54 || 106 || 80 || 119

|-

|}

Filaments: Difference between revisions

Dank (talk | contribs)

@@ Line 30: / Line 30: @@
 ==Bambu filaments parameter table==
 {| wikiclass="table" border="1"
-! Parameter !! PLA Aero !! ASA !! ASA Aero
+! Parameter !! PLA Aero !! ASA !! ASA Aero !! PC
 |-
-| Print temp C || 210-260 || 240-270 || 240-280
+| Print temp C || 210-260 || 240-270 || 240-280 || 250-270
 |-
-| Print speed mm/s || <180 || <250 || <150
+| Print speed mm/s || <180 || <250 || <150 || <300
 |-
-| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80
+| Flow rate ratio || 0.5-0.8 || 0.93-0.97 || 0.45-0.80 ||
 |-
-| Filament density g/cm³ || 1.21 || 1.05 || 0.99
+| Filament density g/cm³ || 1.21 || 1.05 || 0.99 || 1.2
 |-
-| Foaming rate || 0-120 || n/a || 0-110
+| Foaming rate || 0-120 || n/a || 0-110 || n/a
 |-
-| Vol. expansion ratio || 100-220 || 102 || 100-210
+| Vol. expansion ratio || 100-220 || 102 || 100-210 ||
 |-
-| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97
+| Print density g/cm³ || 0.55-1.05 || 1.03 || 0.46-0.97 ||
 |-
-| Tensile strength MPa || 24±2 || 37±3 || 32±4
+| Tensile strength MPa || 24±2 || 37±3 || 32±4 || 55±4
 |-
-| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6
+| Breaking elongation rate || 2.6±0.7 || 9.2±1.4 || 5.1±1.6 || 3.8±0.3
 |-
-| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120
+| Bending modulus MPa || 1690±120 || 1920±130 || 1510±120 || 2310±70
 |-
-| Bending strength MPa || 45±4 || 65±5 || 58±6
+| Bending strength MPa || 45±4 || 65±5 || 58±6 || 108±4
 |-
-| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5
+| Impact strength kJ/m² || 28.8±1.3 || 41.0±2.3 || 32.0±2.5 || 34.8±2.1
 |-
-| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5
+| Melt index g/10min || 7.7±0.6 || 7.0±0.8 || 1.56 ± 0.5 || 32.2±2.9
 |-
-| Melting temp C || 153 || 210 || 204
+| Melting temp C || 153 || 210 || 204 || 228
 |-
-| Heat deflection temp C || 53 || 100 || 85
+| Heat deflection temp C || 53 || 100 || 85 || 117
 |-
-| Vicat softening temp C || 54 || 106 || 80
+| Vicat softening temp C || 54 || 106 || 80 || 119
 |-
 |}