Check out my first novel, midnight's simulacra!

Filaments: Difference between revisions

From dankwiki
Line 51: Line 51:
===Bambu===
===Bambu===
{| class="wikitable sortable" border="1"
{| class="wikitable sortable" border="1"
! Parameter !! Print temp (℃) !! Print speed (mm/s) !! Flow rate ratio !! Density (g/cm³) !! Foaming rate !! Vol. expansion ratio !! Print density (g/cm³) !! Tensile strength (MPa) !! Breaking elongation rate !! Bending modulus (MPa) !! Bending strength (MPa) !! Impact strength (kJ/m²) !! Melt index (g/10min) !! Melting temp (℃ ) !! Heat deflection temp (℃ ) !! Vicat softening temp (℃)
! Parameter !! Print temp (℃) !! Print speed (mm/s) !! Filament density (g/cm³) !! Foaming rate !! Vol. expansion ratio !! Print density (g/cm³) !! Tensile strength (MPa) !! Breaking elongation rate !! Bending modulus (MPa) !! Bending strength (MPa) !! Impact strength (kJ/m²) !! Melt index (g/10min) !! Melting temp (℃ ) !! Heat deflection temp (℃ ) !! Vicat softening temp (℃) !! Flow rate ratio
|-
|-
| PLA Aero || 210 - 260 || <180 || 0.5-0.8 || 1.21 || 0-120 || 100 - 220 || 0.55 - 1.05 || 24 ± 2 || 2.6 ± 0.7 || 1690 ± 120 || 45 ± 4 || 28.8 ± 1.3 || 7.7 ± 0.6 || 153 || 53 || 54
| PLA Aero || 210 - 260 || <180 || 1.21 || 0-120 || 100 - 220 || 0.55 - 1.05 || 24 ± 2 || 2.6 ± 0.7 || 1690 ± 120 || 45 ± 4 || 28.8 ± 1.3 || 7.7 ± 0.6 || 153 || 53 || 54 || 0.5-0.8
|-
|-
| ASA || 240 - 270 || <250 || 0.93-0.97 || 1.05 || n/a || 102 || 1.03 || 37 ± 3 || 9.2 ± 1.4 || 1920 ± 130 || 65 ± 5 || 41.0 ± 2.3 || 7.0 ± 0.8 || 210 || 100 || 106
| ASA || 240 - 270 || <250 || 1.05 || n/a || 102 || 1.03 || 37 ± 3 || 9.2 ± 1.4 || 1920 ± 130 || 65 ± 5 || 41.0 ± 2.3 || 7.0 ± 0.8 || 210 || 100 || 106 || 0.93-0.97
|-
|-
| ASA Aero || 240 - 280 || <150 || 0.45-0.80 || 0.99 || 0-110 || 100 - 210 || 0.46 - 0.97 || 32 ± 4 || 5.1 ± 1.6 || 1510 ± 120 || 58 ± 6 || 32.0 ± 2.5 || 1.56 ± 0.5 || 204 || 85 || 80
| ASA Aero || 240 - 280 || <150 || 0.99 || 0-110 || 100 - 210 || 0.46 - 0.97 || 32 ± 4 || 5.1 ± 1.6 || 1510 ± 120 || 58 ± 6 || 32.0 ± 2.5 || 1.56 ± 0.5 || 204 || 85 || 80 || 0.45-0.80
|-
|-
| PC || 250 - 270 || <300 || || 1.2 || n/a || || || 55 ± 4 || 3.8 ± 0.3 || 2310 ± 70 || 108 ± 4 || 34.8 ± 2.1 || 32.2 ± 2.9 || 228 || 117 || 119
| PC || 250 - 270 || <300 || 1.2 || n/a || || || 55 ± 4 || 3.8 ± 0.3 || 2310 ± 70 || 108 ± 4 || 34.8 ± 2.1 || 32.2 ± 2.9 || 228 || 117 || 119 ||
|-
|- ||
| ABS || 240 - 270 || <300 || || 1.05 || n/a || || || 33 ± 3 || 10.5 ± 1.0 || 1880 ± 110 || 62 ± 4 || 39 ± 3.6 || 34.2 ± 3.8 || 200 || 87 || 94
| ABS || 240 - 270 || <300 || 1.05 || n/a || || || 33 ± 3 || 10.5 ± 1.0 || 1880 ± 110 || 62 ± 4 || 39 ± 3.6 || 34.2 ± 3.8 || 200 || 87 || 94 ||
|-
|- ||
| ABS-GF || 240 - 270 || <180 || || 1.08 || n/a || || || 36 ± 3 || 6.3 ± 1.2 || 2860 ± 130 || 68 ± 4 || 14.5 ± 1.5 || 7.56 ± 1.4 || 202 || 99 || 103
| ABS-GF || 240 - 270 || <180 || 1.08 || n/a || || || 36 ± 3 || 6.3 ± 1.2 || 2860 ± 130 || 68 ± 4 || 14.5 ± 1.5 || 7.56 ± 1.4 || 202 || 99 || 103 ||
|-
|- ||
| PETG-Trans || 230 - 260 || <220 || || 1.25 || n/a || || || 33 ± 4 || 8.2 ± 1.3 || 1610 ± 130 || 68 ± 3 || 37.4 ± 3.3 || 11.7 ± 1.5 || 228 || 74 || 79
| PETG-Trans || 230 - 260 || <220 || 1.25 || n/a || || || 33 ± 4 || 8.2 ± 1.3 || 1610 ± 130 || 68 ± 3 || 37.4 ± 3.3 || 11.7 ± 1.5 || 228 || 74 || 79 ||
|-
|- ||
| PETG-HF || 230 - 260 || <300 || || 1.28 || n/a || || || 34 ± 4 || 8.6 ± 1.2 || 2050 ± 120 || 64 ± 3 || 31.5 ± 2.2 || 28.2 ± 2.7 || 214 || 69 || 70
| PETG-HF || 230 - 260 || <300 || 1.28 || n/a || || || 34 ± 4 || 8.6 ± 1.2 || 2050 ± 120 || 64 ± 3 || 31.5 ± 2.2 || 28.2 ± 2.7 || 214 || 69 || 70 ||
|-
|- ||
| PA6-CF || 260 - 290 || <100 || || 1.09 || n/a || || || 102 ± 7 || 5.8 ± 1.6 || 5460 ± 280 || 151 ± 8 || 40.3 ± 2.5 || 6.8 ± 0.6 || 223 || 186 || 212
| PA6-CF || 260 - 290 || <100 || 1.09 || n/a || || || 102 ± 7 || 5.8 ± 1.6 || 5460 ± 280 || 151 ± 8 || 40.3 ± 2.5 || 6.8 ± 0.6 || 223 || 186 || 212 ||
|-
|- ||
| PPA-CF || 280 - 310 || <100 || || 1.25 || n/a || || || 168 ± 4 || 3.2 ± 0.4 || 9860 ± 480 || 208 ± 6 || 41.7 ± 2.8 || 8.4 ± 0.7 || 258 || 227 || 232
| PPA-CF || 280 - 310 || <100 || 1.25 || n/a || || || 168 ± 4 || 3.2 ± 0.4 || 9860 ± 480 || 208 ± 6 || 41.7 ± 2.8 || 8.4 ± 0.7 || 258 || 227 || 232 ||
|-
|- ||
| PLA-CF || 210 - 240 || <200 || || 1.22 || n/a || || || 38 ± 4 || 8.4 ± 3.2 || 3950 ± 190 || 89 ± 4 || 23.2 ± 3.7 || 3.7 ± 0.6 || 165 || 55 || 69
| PLA-CF || 210 - 240 || <200 || 1.22 || n/a || || || 38 ± 4 || 8.4 ± 3.2 || 3950 ± 190 || 89 ± 4 || 23.2 ± 3.7 || 3.7 ± 0.6 || 165 || 55 || 69 ||
|-
|- ||
| PPS-CF || 310 - 340 || <100 || || 1.26 || n/a || || || 87 ± 5 || 1.2 ± 0.4 || 7160 ± 280 || 142 ± 5 || 27.8 ± 2.3 || 11.48 ± 1.23 || 284 || 264 || 268
| PPS-CF || 310 - 340 || <100 || 1.26 || n/a || || || 87 ± 5 || 1.2 ± 0.4 || 7160 ± 280 || 142 ± 5 || 27.8 ± 2.3 || 11.48 ± 1.23 || 284 || 264 || 268 ||
|-
|- ||
| PAHT-CF || 260 - 290 || <100 || || 1.06 || n/a || || || 92 ± 7 || 8.4 ± 1.8 || 4230 ± 210 || 125 ± 7 || 57.5 ± 3.4 || 14.4 ± 2.0 || 225 || 194 || 220
| PAHT-CF || 260 - 290 || <100 || 1.06 || n/a || || || 92 ± 7 || 8.4 ± 1.8 || 4230 ± 210 || 125 ± 7 || 57.5 ± 3.4 || 14.4 ± 2.0 || 225 || 194 || 220 ||
|-
|- ||
| ASA-CF || 250 - 280 || <250 || || 1.02 || n/a || || || 34 ± 3 || 9.6 ± 1.4 || 3740 ± 130 || 72 ± 5 || 14.0 ± 2.2 || 1.74 ± 0.3 || 210 || 110 || 108
| ASA-CF || 250 - 280 || <250 || 1.02 || n/a || || || 34 ± 3 || 9.6 ± 1.4 || 3740 ± 130 || 72 ± 5 || 14.0 ± 2.2 || 1.74 ± 0.3 || 210 || 110 || 108 ||
|-
|- ||
| PA6-GF || 260 - 290 || <130 || || 1.14 || n/a || || || 75 ± 6 || 3.9 ± 0.8 || 3670 ± 140 || 120 ± 6 || 27.7 ± 2.2 || 9.0 ± 0.8 || 219 || 182 || 210
| PA6-GF || 260 - 290 || <130 || 1.14 || n/a || || || 75 ± 6 || 3.9 ± 0.8 || 3670 ± 140 || 120 ± 6 || 27.7 ± 2.2 || 9.0 ± 0.8 || 219 || 182 || 210 ||
|-
|-
|}
|}
[[CATEGORY: 3D Printing]]
[[CATEGORY: 3D Printing]]

Revision as of 10:37, 29 November 2024

Keeping notes on various FDM filaments here. The glass transition temperature is ideal for annealling. I've got a Google Sheet now chronicling experience with individual filaments.

Qualitative comparisons

Manufacturers employ additives to change the properties of their filaments, which I don't attempt to address here. Properties may change across different batches of the same filament. These are very rough comparisons based off oral wisdom.

  • Impact strength: ASA > ABS > PC > PETG > PLA
  • Tensile strength: PA >> PC >> ASA > ABS/PETG > PLA
  • UV resistance: ASA > ABS
  • "Chemical" resistance: PETG > ABS
  • Melting temp: PC > ASA > PETG > ABS >> PLA
  • Heat resistance: PC > ASA > ABS > PETG > PLA
  • Printing speed:
  • Offensiveness (odor, VOCs while printing): ABS > ASA, PA, PC
  • Acetone postprocessing: ASA/ABS only
  • Ease of sanding: PLA > PETG > ABS/ASA
  • Ease of painting: PLA > PETG > ABS/ASA
  • Tendency to warp: PC > ABS/ASA > PLA > PETG
  • Hygroscopicity: PA/TPU > PETG/ABS/ASA > PLA
  • Filament density: PETG/PLA > ABS/ASA
  • Hotend temp required: PC > ABS/ASA > PETG > PLA

Tables

These data come from the manufacturers' websites and datasheets, and have not been verified. Different manufacturers report different data. These tables are not exhaustive.

Polymaker

Filament Density (g/cm³) Glass transition (℃) Vicat softening (℃) Heat deflection (℃) Young's modulus XY (MPa) Young's modulus Z (MPa) Tensile strength XY (MPa) Tensile strength Z (MPa) Bending modulus XY (MPa) Charpy XY (kJ/m²) MSRP ($/kg)
PC-ABS 1.1 109 135 112 1835 1677 40 23 2081 26 49.99
PolyMax PC 1.19 113 117 114 2436 2150 53 41 2050 21 51.99
PolyMax PC-FR 1.2 115 116 110 2634 2743 67 46 2518 11.7 54.99
Polymaker PC-PBT 1.2 140 139 107 1849 1659 43 29 1934 21 54.99
Fiberon PET-CF17 1.34 79 238 148 5481 3559 66 28 4744 5 49.98
Fiberon PA6-GF25 1.2 70 191 4431 3330 85 61 4637 17 59.98
Fiberon PPS-CF10 1.29 98 268 253 5314 2790 36 32 4647 5 139.98
PolyLite PC 1.19 113 120 111 2497 2371 69 53 2640 4 29.99
Fiberon PA6-CF20 1.17 74 215 7454 4355 105 68 8339 13 79.98
Fiberon PA12-CF10 1.06 55 131 3304 1801 72 43 3535 13 139.98

Bambu

Parameter Print temp (℃) Print speed (mm/s) Filament density (g/cm³) Foaming rate Vol. expansion ratio Print density (g/cm³) Tensile strength (MPa) Breaking elongation rate Bending modulus (MPa) Bending strength (MPa) Impact strength (kJ/m²) Melt index (g/10min) Melting temp (℃ ) Heat deflection temp (℃ ) Vicat softening temp (℃) Flow rate ratio
PLA Aero 210 - 260 <180 1.21 0-120 100 - 220 0.55 - 1.05 24 ± 2 2.6 ± 0.7 1690 ± 120 45 ± 4 28.8 ± 1.3 7.7 ± 0.6 153 53 54 0.5-0.8
ASA 240 - 270 <250 1.05 n/a 102 1.03 37 ± 3 9.2 ± 1.4 1920 ± 130 65 ± 5 41.0 ± 2.3 7.0 ± 0.8 210 100 106 0.93-0.97
ASA Aero 240 - 280 <150 0.99 0-110 100 - 210 0.46 - 0.97 32 ± 4 5.1 ± 1.6 1510 ± 120 58 ± 6 32.0 ± 2.5 1.56 ± 0.5 204 85 80 0.45-0.80
PC 250 - 270 <300 1.2 n/a 55 ± 4 3.8 ± 0.3 2310 ± 70 108 ± 4 34.8 ± 2.1 32.2 ± 2.9 228 117 119
ABS 240 - 270 <300 1.05 n/a 33 ± 3 10.5 ± 1.0 1880 ± 110 62 ± 4 39 ± 3.6 34.2 ± 3.8 200 87 94
ABS-GF 240 - 270 <180 1.08 n/a 36 ± 3 6.3 ± 1.2 2860 ± 130 68 ± 4 14.5 ± 1.5 7.56 ± 1.4 202 99 103
PETG-Trans 230 - 260 <220 1.25 n/a 33 ± 4 8.2 ± 1.3 1610 ± 130 68 ± 3 37.4 ± 3.3 11.7 ± 1.5 228 74 79
PETG-HF 230 - 260 <300 1.28 n/a 34 ± 4 8.6 ± 1.2 2050 ± 120 64 ± 3 31.5 ± 2.2 28.2 ± 2.7 214 69 70
PA6-CF 260 - 290 <100 1.09 n/a 102 ± 7 5.8 ± 1.6 5460 ± 280 151 ± 8 40.3 ± 2.5 6.8 ± 0.6 223 186 212
PPA-CF 280 - 310 <100 1.25 n/a 168 ± 4 3.2 ± 0.4 9860 ± 480 208 ± 6 41.7 ± 2.8 8.4 ± 0.7 258 227 232
PLA-CF 210 - 240 <200 1.22 n/a 38 ± 4 8.4 ± 3.2 3950 ± 190 89 ± 4 23.2 ± 3.7 3.7 ± 0.6 165 55 69
PPS-CF 310 - 340 <100 1.26 n/a 87 ± 5 1.2 ± 0.4 7160 ± 280 142 ± 5 27.8 ± 2.3 11.48 ± 1.23 284 264 268
PAHT-CF 260 - 290 <100 1.06 n/a 92 ± 7 8.4 ± 1.8 4230 ± 210 125 ± 7 57.5 ± 3.4 14.4 ± 2.0 225 194 220
ASA-CF 250 - 280 <250 1.02 n/a 34 ± 3 9.6 ± 1.4 3740 ± 130 72 ± 5 14.0 ± 2.2 1.74 ± 0.3 210 110 108
PA6-GF 260 - 290 <130 1.14 n/a 75 ± 6 3.9 ± 0.8 3670 ± 140 120 ± 6 27.7 ± 2.2 9.0 ± 0.8 219 182 210
Retrieved from "https://nick-black.com/dankwiki/index.php?title=Filaments&oldid=11357"