Schwarzgerät III upgrade: Difference between revisions
| (16 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
==Summary of changes== | ==Summary of changes== | ||
[[File:Schwarz-loop.png|thumb|right|Custom loop]] | |||
* '''New hardware''': | * '''New hardware''': | ||
** Added 12V RGB+fan hub to the top of the PSU side | ** Added 12V RGB+fan hub to the top of the PSU side | ||
| Line 33: | Line 34: | ||
==New cooling configuration== | ==New cooling configuration== | ||
[[File:Schwarz-cool.png|thumb|Fan setup]] | |||
Coolant temperatures are sampled at both reservoirs. The Monsoon sensor feeds into the Corsair, while the Quantum sensors feeds into the motherboard. Ambient temperatures are sampled via two sensors immediately outside the rear of the motherboard side, towards the bottom. One feeds into the Corsair, and one feeds into the motherboard. Currently, all PWM is then controlled based off absolute coolant temperature, but ideally it would be controlled using the difference between coolant and ambient temperatures. | Coolant temperatures are sampled at both reservoirs. The Monsoon sensor feeds into the Corsair, while the Quantum sensors feeds into the motherboard. Ambient temperatures are sampled via two sensors immediately outside the rear of the motherboard side, towards the bottom. One feeds into the Corsair, and one feeds into the motherboard. Currently, all PWM is then controlled based off absolute coolant temperature, but ideally it would be controlled using the difference between coolant and ambient temperatures. | ||
| Line 117: | Line 119: | ||
==Fans== | ==Fans== | ||
All fans are 12V. The [[Phanteks|Phanteks T30s]] have an "Advanced" switch enabling 3000RPM, but I am not using it. All values listed are maxima; I am typically running them well below these settings. All radiators save the GTR360 are using push+pull. All fans are controlled via PWM. | All fans are 12V. The [[Phanteks|Phanteks T30s]] have an "Advanced" switch enabling 3000RPM, but I am not using it. All values listed are maxima; I am typically running them well below these settings. All radiators save the GTR360 are using push+pull. All fans are controlled via PWM. | ||
| Line 183: | Line 184: | ||
===Control=== | ===Control=== | ||
Pump 5A and 5B cannot be controlled independently, nor can Pump 6A and Pump 6B. | |||
CPU0 can only use the CPU temperature as its control. | |||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
! Source !! Input !! Destination !! Outputs | ! Source !! Input !! Destination !! Outputs | ||
|- | |||
| CPU0 || CPU || Dual XTOP D5s || PWM | |||
|- | |- | ||
| CPU1 || Coolant (mobo) || Silverstone || PWM | | CPU1 || Coolant (mobo) || Silverstone || PWM | ||
| Line 190: | Line 196: | ||
| SYS1 || Coolant (mobo) || 12V hub || PWM | | SYS1 || Coolant (mobo) || 12V hub || PWM | ||
|- | |- | ||
| SYS2 || || || | | SYS2 || Coolant (mobo) || 2x Noctua NF-P12 redux-1700 || 12V, PWM | ||
|- | |- | ||
| Pump 5A || Coolant (mobo) || | | Pump 5A || Coolant (mobo) || Phanteks T30 || 12V, PWM | ||
|- | |- | ||
| Pump 5B || Coolant (mobo) || | | Pump 5B || Coolant (mobo) || Phanteks T30 || 12V, PWM | ||
|- | |- | ||
| Pump 6A || || || | | Pump 6A || Coolant (mobo) || Noctua NF-F12 || PWM, 12V | ||
|- | |- | ||
| Pump 6B || | | Pump 6B || || || | ||
|- | |- | ||
| Silverstone || CPU1 PWM || | | Silverstone || CPU1 PWM || 4x Phanteks T30, 2x EK-Vardar, Noctua NF-A12x25, 2x Noctua NF-A8, Noctua NF-F12 || 12V, PWM | ||
|- | |- | ||
| 12V hub || SYS1 PWM || 2x NF-F12 iPPC-2000, NF-F12 iPPC-3000 || 12V, PWM | | 12V hub || SYS1 PWM || 2x NF-F12 iPPC-2000, NF-F12 iPPC-3000 || 12V, PWM | ||
|- | |- | ||
| Corsair || Coolant (Corsair) || 2x Phanteks T30, 2x Noctua NF-A12x25, Noctua NF-A14 || 12V, PWM | | Corsair || Coolant (Corsair) || 2x Phanteks T30, 2x Noctua NF-A12x25, 2x Noctua NF-A14 || 12V, PWM | ||
|- | |- | ||
|} | |} | ||
==Bespoke parts== | ==Bespoke parts== | ||
I've got a number of self-designed 3d-printed (using my [[Voxel]]) parts in the machine. The OpenSCAD source for all such objects is available on [https://github.com/dankamongmen/openscad-models GitHub]. | I've got a number of self-designed 3d-printed (using my old [[Voxel]], or my newer [[Qidi]]) parts in the machine. The OpenSCAD source for all such objects is available on [https://github.com/dankamongmen/openscad-models GitHub]. | ||
<gallery> | <gallery> | ||
File:Xtopbrace.jpg|Front mount for XTOP Dual D5 | File:Xtopbrace.jpg|Front mount for XTOP Dual D5 (Hatchbox PLA) | ||
File:3dprinted-xtopmountfront.jpg|Rear mount for XTOP Dual D5 | File:3dprinted-xtopmountfront.jpg|Rear mount for XTOP Dual D5 (Hatchbox PLA) | ||
File:3dprinted-cableback.jpg|Rear cable shroud | File:Backbrace.jpg|Back cover for XTOP Dual D5 (Atomic Filament PETG) | ||
File:3dprinted-cablefront.jpg|Front cable shroud | File:3dprinted-cableback.jpg|Rear cable shroud (Atomic Filament PLA) | ||
File:Cablebracket.jpg|PCIe slot cover with cable guide | File:3dprinted-cablefront.jpg|Front cable shroud (Atomic Filament PLA) | ||
File:Birdcover.jpg|Antenna mount covering Quantum FLT brackets | File:Cablebracket.jpg|PCIe slot cover with cable guide (Hatchbox PLA) | ||
File:VAMOLED.jpg|Enclosure for [[Waveshare_AMOLED|Waveshare 5.5" AMOLED]] | File:Birdcover.jpg|Antenna mount covering Quantum FLT brackets (Hatchbox PLA) | ||
File:VAMOLED.jpg|Enclosure for [[Waveshare_AMOLED|Waveshare 5.5" AMOLED]] (Atomic Filament carbon fiber PETG) | |||
File:Molexplug.jpg|Plug with a Molex-sized channel (Hatchbox PLA) | |||
File:Molexplug-installed.jpg|The installed plug allows LED light through | |||
File:Cpuplug.jpg|Shroud for CPU power cables + fan cables (Atomic Filament PLA) | |||
File:Cage-shroud.jpg|Shroud for PSU-side disk cages (Atomic Filament PLA) | |||
File:Moboshroud.jpg|Shroud for motherboard-side disk enclosures (Atomic Filament CF-PETG and PLA) | |||
</gallery> | </gallery> | ||
==Project Pompidou== | ===Project Pompidou=== | ||
My cabling situation on the PSU side is a mess. Inspired by the [https://en.wikipedia.org/wiki/Centre_Pompidou Centre Pompidou], I'm going to design and print skychannels in which to run the power cables. Ideally, none of them will be seen. To do this, I need: | My cabling situation on the PSU side is a mess. Inspired by the [https://en.wikipedia.org/wiki/Centre_Pompidou Centre Pompidou], I'm going to design and print skychannels in which to run the power cables. Ideally, none of them will be seen. To do this, I need: | ||
| Line 228: | Line 238: | ||
* Channels into which I can lay the cables, probably doubling them up. These channels will need run from the PSU to their targets. | * Channels into which I can lay the cables, probably doubling them up. These channels will need run from the PSU to their targets. | ||
* Something at the hookup points | * Something at the hookup points | ||
==External links== | |||
* [https://imgur.com/a/cl9Yf Project M8] by [https://www.reddit.com/user/p0Pe/ u/p0Pe] appears to have done something very similar to the Pompidou Project a full decade ago. nice work. | |||
[[CATEGORY: Hardware]] | [[CATEGORY: Hardware]] | ||