First introduced on the Illiac IV, and not to be confused with vector processing. SIMD-capable units are often taxonomized via SIMDnXm nomenclature, where n is the issue width and m is the channel width; a superscalar processor would be SIMDnX1, while a scalar SISD processor would be SIMD1X1.
Compilers and Assemblers
- GCC can issue SIMD four different ways:
Data Types (taken from SSE specs)
These do not necessarily map to C data types of the same name, for any given compiler!
- half precision: 16-bit IEEE 754 floating-point (bias-15) (IEEE 754 2008 binary16)
- single: 32-bit IEEE 754 floating-point (bias-127) (IEEE 754 2008 binary32)
- double: 64-bit IEEE 754 floating-point (bias-1023) (IEEE 754 2008 binary64)
- long double: 80-bit "double extended" IEEE 754-1985 floating-point (bias-16383)
- not an actual SIMD type, but an artifact of x87
- word: 32-bit two's complement integer
- doubleword, dword: 64-bit two's complement integer
The AVX (Advanced Vector eXtensions) were introduced on Intel's Sandy Bridge (2010) and AMD's Bulldozer (2011). They operate on the 256-bit YMM registers (YMM0..YMM15), which are aliased by the XMM registers. They are encoded using the VEX scheme. Support for AVX can be determined via:
- Determine that CPUID.1:ECX.OSXSAVE[bit 27] is set (XGETBV is enabled for application use)
- Issue XGETBV and verify that XFEATURE_ENABLED_MASK[2:1] = 0x3 (XMM state and YMM state are enabled by OS)
- Determine that CPUID.1:ECX.AVX[bit 28] is set (AVX instructions supported)
New 256-bit YMM registers.
New Haswell Instructions
- AVX2 instructions: integer SIMD using AVX's 256-bit YMM registers.
- YMM-SIMD bit manipulation, permute, gather, shift, and FMA
- Introduced on Sandy Bridge
The Streaming SIMD Extensions operate on the 128-bit XMM registers (XMM0..XMM7 in 32-bit mode, XMM0..XMM15 in 64-bit mode). In its original incarnation on the PIII, execution units (but not registers) were shared with the x87 floating-point architecture. The execution units were separated in the NetBurst microarchitecture. In the Core microarchitecture, the execution engine has been widened for greater SSE throughput.
- Unimplemented extensions competing with SSE4, encoded using a method incompatible with VEX
- Withdrawn, converted into VEX-compatible encodings, and split into:
- FMA4: Fused floating-point multiply-add (compare Intel's FMA)
- XOP: Fused integer multiply-add, byte permutations, shifts, rotates, integer vector horizontal operations (compare Intel's SSE4)
- CVT16: Half-precision conversion
- Introduced on Penryn
- dpps -- dot product of two vectors having four single components each
- dppd -- dot product of two vectors having two double components each
- Introduced on Nehalem
- Originally known as Prescott New Instructions, and introduced on P4-Prescott
- movddup -- move a double from a 8-byte-aligned memory location or lower half of XMM register to upper half, then duplicate upper half to lower half
- Introduced with the Core microarchitecture. Sometimes referred to as Tejas New Instructions or Merom New Instructions
- pmaddwd -- multiply packed words, then horizontally sum pairs, accumulating into doublewords
- Introduced with the P4.
- Extends the MMX instructions to XMM registers.
- movapd -- move two packed doubles from a 16-byte-aligned memory location to XMM registers, or vice versa, or between two XMM registers.
- movupd -- movapd safe for unaligned memory references, with far inferior performance.
- mulpd -- multiply two packed doubles. the multiplier is a 16-byte-aligned memory location or XMM register. the target XMM register serves as the multiplicand.
- addpd -- add two packed doubles. the addend is a 16-byte-aligned memory location or XMM register. the target XMM register serves as the augend.
- Introduced with the PIII. Sometimes referred to as Katmai New Instructions, and branded for some time as the Internet Streaming SIMD Extensions
- movaps -- move four packed singles from a 16-byte-aligned memory location to XMM registers, or vice versa, or between two XMM registers.
- movups -- movaps safe for unaligned memory references, with far inferior performance.
- mulps -- multiply four packed singles. the multiplier is a 16-byte-aligned memory location or XMM register. the target XMM register serves as the multiplicand.
- addps -- add four packed singles. the addend is a 16-byte-aligned memory location or XMM register. the target XMM register serves as the augend.
- The FMA instruction set extension to x86 should hit around 2011, providing floating-point fused multiply-add
- AMD appears to call this FMA4, part of what was SSE5
- PowerPC implements AltiVec
- SPARC implements VIS, the Visual Instruction Set
- PA-RISC implements MAX, the Multimedia Acceleration eXtensions
- ARM implements NEON
- Alpha implemented MVI, the Motion Video Instructions
- SWAR: SIMD Within a Register (bit-parallel methods)
- "Why no FMA in AVX in Sandy Bridge?", Intel Developers Forum
- SSE5 guide at AMD
- SSE4 reference at Intel
- 2007-04-19 post to http://virtualdub.org, "SSE4 finally adds dot products"
- AMD64 Architecture Programmer’s Manual Volume 6: 128-Bit and 256-Bit XOP, FMA4 and CVT16 Instructions
- Agner Fog's x86 Instruction Tables
- "Haswell New Instruction Descriptions now Available", Intel Software Developer Network, 2011-06-13
- General architecture page