Three recent physical projects: Difference between revisions

(4 intermediate revisions by the same user not shown)

Line 1:

'''[[Dankblog|dankblog!]] 2024-06-22, ~~2334 EST~~, at [[Viewpoint|the danktower]]'''

'''[[Dankblog|dankblog!]] 2024-06-22, 0130 EDT, at [[Viewpoint|the danktower]]'''

[[File:Printingstation.jpg|frame|my printing station]]

I recently got my [https://bambulab.com/en/x1 Bambu X1 Carbon] working again, after being offline for almost two years. Doing so motivated me to knock out some projects I'd been contemplating.

Line 37:

==Case faceplate with OLED display==

I'd already [[Waveshare_AMOLED|designed this faceplate]] and the AMOLED+[[Raspberry_Pi|Raspberry Pi]] that sits inside. I added a strip of high-intensity CoB LEDs, as long intended. I reprinted it using black ABS. To power the 12V LEDs, I took a SATA power cable and cut off the female end. I then separated the five cables. Bifurcate the ground wire, and solder a ground + 12V to the LED strip. SATA provides 5V and 12V (and sometimes 3.3V, unnecessary here), so we'll use the 5V to power the Pi+AMOLED (this will provide more amperage than a USB hookup). Bifurcate the 5V and second ground line, and solder one pair to each of two USB-µA plugs. Thread the LED strip through the faceplate in front of the OLED.

[[File:Frontplate-leds.jpg|frame]]

Beautiful! Tremendous! This occupies two 5.25" bays.

==Filter tower==

Some filament types produce toxins when printed, including my workhorse ABS. It thus seems sensible to try and filter some of the VOCs. There's a lovely "[https://www.printables.com/model/272525-bentobox-v20-carbon-filter-for-bambu-lab-x1c-enclo BentoBox]" model for the Bambu X1C on Thingiverse. Grab it, and print the seven necessary components (I used ABS). They'll snap into one another, and you can add 2mm disk magnets to improve on things. I had numerous high-power 12V (6+ krpm) 40mm fans extracted from a [[A_Rack_of_One%27s_Own|Supermicro 4U server]] lying around, perfect for the BentoBox. I added activated acid-free charcoal and a HEPA filter and connected the two fans with a Y cable. There were now two problems:

* How to power the fans?

* How to control the fans?

I only wanted the (loud) fans to run when I was actually printing toxic materials. The easiest way to do this was a NO (normally open) temperature switch. Only toxic materials require heating the chamber up to 35C or higher, and I keep the Danktower significantly cooler than that (35C~=95F). Then, to drive the fans off the 24V of the Bambu, I used an efficient, cheap LM2596 buck converter. Easy peasy!

'''previously: "[[The_beginning_of_the_end_of_iptables|The beginning of the end of iptables]]" 2024-04-19'''

[[Category:Blog]]

[[Category:Projects]]

@@ Line 1: / Line 1: @@
-'''[[Dankblog|dankblog!]] 2024-06-22, 2334 EST, at [[Viewpoint|the danktower]]'''
+'''[[Dankblog|dankblog!]] 2024-06-22, 0130 EDT, at [[Viewpoint|the danktower]]'''
 [[File:Printingstation.jpg|frame|my printing station]]
 I recently got my [https://bambulab.com/en/x1 Bambu X1 Carbon] working again, after being offline for almost two years. Doing so motivated me to knock out some projects I'd been contemplating.
@@ Line 37: / Line 37: @@
 ==Case faceplate with OLED display==
+I'd already [[Waveshare_AMOLED|designed this faceplate]] and the AMOLED+[[Raspberry_Pi|Raspberry Pi]] that sits inside. I added a strip of high-intensity CoB LEDs, as long intended. I reprinted it using black ABS. To power the 12V LEDs, I took a SATA power cable and cut off the female end. I then separated the five cables. Bifurcate the ground wire, and solder a ground + 12V to the LED strip. SATA provides 5V and 12V (and sometimes 3.3V, unnecessary here), so we'll use the 5V to power the Pi+AMOLED (this will provide more amperage than a USB hookup). Bifurcate the 5V and second ground line, and solder one pair to each of two USB-µA plugs. Thread the LED strip through the faceplate in front of the OLED.
+[[File:Frontplate-leds.jpg|frame]]
+Beautiful! Tremendous! This occupies two 5.25" bays.
 ==Filter tower==
+Some filament types produce toxins when printed, including my workhorse ABS. It thus seems sensible to try and filter some of the VOCs. There's a lovely "[https://www.printables.com/model/272525-bentobox-v20-carbon-filter-for-bambu-lab-x1c-enclo BentoBox]" model for the Bambu X1C on Thingiverse. Grab it, and print the seven necessary components (I used ABS). They'll snap into one another, and you can add 2mm disk magnets to improve on things. I had numerous high-power 12V (6+ krpm) 40mm fans extracted from a [[A_Rack_of_One%27s_Own|Supermicro 4U server]] lying around, perfect for the BentoBox. I added activated acid-free charcoal and a HEPA filter and connected the two fans with a Y cable. There were now two problems:
+* How to power the fans?
+* How to control the fans?
+I only wanted the (loud) fans to run when I was actually printing toxic materials. The easiest way to do this was a NO (normally open) temperature switch. Only toxic materials require heating the chamber up to 35C or higher, and I keep the Danktower significantly cooler than that (35C~=95F). Then, to drive the fans off the 24V of the Bambu, I used an efficient, cheap LM2596 buck converter. Easy peasy!
 '''previously: "[[The_beginning_of_the_end_of_iptables|The beginning of the end of iptables]]" 2024-04-19'''
 [[Category:Blog]]
+[[Category:Projects]]

Three recent physical projects: Difference between revisions

Dank (talk | contribs)